More turquoise water

Back in 2014 I was fascinated by the bright turquoise water that emerged from a base excavation at the Aruwakkalu limestone mine in Sri Lanka. I was doing my undergraduate internship at the time and was so intrigued that I researched into the phenomenon and wrote a blog post explaining how the turquoise colour emerges due to selective scattering of light caused by calcium carbonate crystals. A picture that I took was also featured in the Mining magazine. Four years later I came across the striking turquoise water again.

I am currently a visiting research student at the University of British Columbia, Canada and recently visited some glacial lakes in British Columbia. I got to see once again, the bright turquoise colour that intrigued me 4 years ago. The reason behind the turquoise colour is the same selective scattering of light. This is caused however, not by calcium carbonate crystals but by glacial flour/rock flour, which is the name given to very fine rock particles generated by glacial erosion, and remain suspended in the water. The lakes I visited were the three Jofrre lakes and Garibaldi lake, where I even went for a relaxing swim. Some pictures that I took at the lakes are below.

Upper Joffre Lake

Middle Joffre Lake

Garibaldi Lake

Garibaldi Lake

Astrophotography on a budget

Astrophotography is thought to be an expensive hobby to pursue involving lots of high-tech and expensive equipment. I was under the same impression and was concerned of this steep entry barrier. Then I came across this blog-Lonely Speck by Ian Norman, who in my opinion, is a very creative photographer and does an excellent job of explaining the basics of photographing the stars. This blog got me started and I started reading online forums and learning about the hobby.

I gathered that new sensors in most cameras-even entry level ones are perfectly capable of capturing the milky way. Any DSLR or compact camera with manual controls can be used to gather enough light over a long exposure to shoot the night sky. So I bought my first DSLR, a Canon 1300D and a basic tripod for about 500AUD. This is an entry level camera and is one of the cheapest DSLRs in the market. Some blog posts and YouTube videos later I set off in search of dark skies.  

After a couple of attempts I am very happy with my results and have even got better results than some photos that I drew inspiration from. I'm still learning and hoping to improve on my methods and results. The usual process I follow to shoot the stars is, waiting for a day with clear skies, checking the moon phase, the position of the milky way and selecting a dark location without much light pollution.  The pictures below are some of my best shots taken up to now, with a little description on the story behind the shot. 

My first attempt at shooting the Milky Way. The stars are out of focus and not a very good image, but was a valuable learning experience. Location:Paradise beach Gippsland

These three shots were taken at Silvan Dam Olinda. The first using the 18mm kit lens and the other two using a 50mm prime lens at f2.0 borrowed from a friend.  

My first shot of the galactic core taken at the Cape Schanck beach. It was a misty day with plenty of moonlight to illuminate the landscape. But the milky way was very faint. 

Clearly visible galactic core taken at Olinda

Another shot of the galactic core taken at Wilsons Prom under moonlight.

This shot was also taken at Wilsons Prom after the moon set. This was the best naked eye view of the Milky Way I've experienced up to now. 

This shot taken at Olinda is one of my favorites because of the unintentional effect of light painting. A car passed by during exposure and it illuminated the tree and a power line nearby, giving the photo a more balanced look.  

Physical Modelling of Coastal Structures

While computational modelling is increasingly being used in place of physical modelling in many fields of engineering, physical modelling still finds an important role in coastal engineering. In the designing and testing of coastal engineering structures such as breakwaters, sea walls and revetments, the complex interactions between waves, sediments and the structural components need to be assessed and quantified. Owing to the high complexity, current numerical and analytical techniques cannot be applied to get a comprehensive solution within a practical time-frame. For this reason despite the relatively high cost involved, physical modelling is relied upon for an accurate assessment of how the real world structure will behave. Usually the final step in the design process of a coastal structure, it serves as a verification of the design calculations and is also a key step in the final project approval.

Physical modelling for coastal structures can be broadly classified into 2D or wave flume testing and 3D or wave basin testing. As the name suggests, 2D tests involve direct wave impact channeled along a long, narrow wave tank known as the flume. Flume tests are mainly used to assess the structural stability of the engineered design, Displacement of structural components, wave over topping and overall structural integrity are monitored over different types of wave attack. 3D tests involve an accurately scaled down construction of the seafloor, or bathymetry over which oceanic conditions of the locality are recreated. It is used to test the structure over waves from different directions and magnitudes. It helps to identify critical locations of the structure. 

The following is a video of a wave flume test carried out at the Lanka Hydraulic Institute (LHI) in Sri Lanka.

Although physical modelling is preferred over computational methods at present, this situation is likely to change in the near future. With increasingly powerful computers and efficient numerical methods being developed, the time taken to run complex simulations have come down significantly. A very promising computational method which could be used for these types of testing is, Smoothed Particle Hydrodynamics (SPH) first developed by Gingold and Monaghan (1977). A mesh free method which models the behavior of a set of particles under a given set of constitutive relations, SPH has already been used in oceanographic research. SPH can also be used to model wave structure interactions and other complex phenomena making it the ideal method for evaluating designs of coastal structures. 

Connecting Adam's Bridge

Adam's Bridge, the collection of limestone shoals between the Mannar Island of Sri Lanka, and the Pamban Island of South India has sparked both the imagination and inventive thinking of many. The closest distance between the two countries-between Dhanushkodi, and Talaimannar is about 30 km, and a bridge connecting the two countries has been a long argued prospect. Such a bridge will be beneficial to both countries in terms of economics and trade. The engineering and environmental challenges of such a construction are overwhelming and a unique Geo-chemical engineering method might hold the answer to this problem.

The Jaffna Peninsula and the surrounding area consists of a Miocene limestone basement and the sea in the area of the Palk Strait is very shallow. This makes it possible to easily construct a permanent causeway between the two countries by connecting the limestone shoals of the Adam's Bridge. Although a simple construction, a permanent separating structure will disrupt the sediment movement through that channel and can be detrimental to fisheries as well. The complete disconnection of the water circulation through the gap can pose significant environmental problems. Building a bridge across the entire span is a possibility that is too costly. Therefore the ideal solution would be to construct a combined, landmass-bridge structure.

http://www.geo.shimane-u.ac.jp/spfs/g_students/mext/08sansfica/Sansfica08_2L.jpg

 To support the construction of a bridge, the existing landmasses or shoals should be elevated. Bridges can be constructed on these elevated landmasses while leaving gaps for the flow of water. Some of these gaps can be dredged deeper to allow for the same volume of water to flow. This could also serve the purpose of a navigable channel for ships as proposed by the Sethusamudram Project. Another prospect is for electricity generation by means of hydro-turbines installed at gaps where the flow of water will be heightened.

It is in elevating these landmasses that the unique geo-chemical engineering method comes into play. Research conducted by Prof. R.D. Schuiling indicates that these landmasses can be elevated in a cost effective manner by injecting Sulphuric acid into the limestone basement. The principle here is that, Sulphuric acid will react with the limestone to produce Gypsum, which has a higher molar volume. Thus, the rock will expand, and this expansion will be accommodated by surface uplift. (R.D.Schuiling, Current Science Vol 86).

This process involves drilling bore holes along the trend of the Adam's bridge and injecting Sulphuric Acid at modest pressures insufficient for hydro-fracturing. The well jointed Miocene limestone is expected to facilitate the migration of the acid through the basement. The acid will be injected to bottom layers of the limestone leaving the top layers unaffected thus avoiding contact with the biosphere and and associated environmental problems.

Prof. Schuiling points out that if industrial waste Sulphuric acid is used for the process it would be an economically viable technology while also solving the disposal problem of such acids. He further addresses possible environmental effects. Since the expansion of the rock takes place at the bottom layers and is separated by a layer of un-reacted limestone, there won't be direct consequence from the reaction. As for the concerns with heavy metals if waste acids are used, it has been experimentally proven that such heavy metals are immobilized during the reaction.

While a social and political consensus regarding the construction of the Adam's Bridge has not yet been reached, and no comprehensive EIA has been conducted in this regard, if these happen in the near future and if the two countries go ahead with the project, this Geo-chemical engineering technology will be a compelling prospect.

Beach Nourishment in Sri Lanka

Beach Erosion is a problem faced by many countries and erosion mitigation has been traditionally done using hard engineering solutions such a seawalls, revetments, groins and breakwaters. However, research in this field has identified that such engineered structures are not suitable as long term solutions for erosion as they interfere with the dynamic coastal processes. It has also been suggested that soft engineering solutions which work along with these coastal processes are the best approach in solving the problem of beach erosion. Beach nourishment is currently the most popular soft engineering solution and is increasingly being used to protect beaches all around the world. Sri Lanka has also joined this trend and completed its first beach nourishment program along a 1.8km stretch in the the Uswetakeiyawa Palliyawatta area in early 2012.

The project involved a large capital investment and a total of volume of 300,000 cubic meters had been used in the nourishment process. The sand used to nourish the beach was offshore sand dredged using a vessel anchored far away from the coastal zone. This is important because, using sand in the coastal zone itself would have been ineffective. The dredged sand had been pumped via pipeline and released as a slurry onshore and the beach reconstructed using earth moving equipment. Several offshore breakwaters had also been constructed with the intention of retaining the nourishing sand. While the project seemed to be an initial success with positive results shown in surveys carried out immediately before and after the project, over a period of time it is evident that the nourishment has not changed the rate of erosion. At present, the beach has once again severely eroded and continues to erode despite the breakwaters.

Severe erosion of the nourished sand

The success of a beach nourishment program depends on many factors. Coastal processes such as waves, near-shore currents, tides and even wind affect the nourishment process. Parameters such as beach profile and gradient and grain size of sand also matters in this regard. For this reason, a beach nourishment effort is site specific and all these site specific data needs to be considered when planning a nourishment program. In addition, it also vital to continuously monitor the performance of the beach after nourishment and to take necessary remedial action to maintain the project.

While most of the above information had been gathered prior to the nourishment project at Uswetakaiyyawa, the effort has fallen short in post project monitoring. The construction of breakwaters to retain the sand being a tried and tested method, has failed to perform properly possibly due to incorrect layout and dimensions of the breakwaters. Our final year research project aims to assess the performance of this nourishment effort and to provide a solution to the problems faced in this project.

To do this, beach profile measurements are taken using a dumpy level and total station along transects perpendicular to the nourished coastal strip. This process is done during several visits to the area covering the main seasonal cycle of the country. This data is used to model the beach profile and to analyse the sand volume changes with respect to time. A particle size analysis is performed on samples collected at each transect and will be used to determine the direction and severity of the sand transport. In addition to this, a temporal analysis of satellite images is also expected to be incorporated in the research in order to further enhance the field data. Using these findings, our research team expects to propose a suitable solution to minimize the rate of erosion and provide a methodology to effectively monitor beach nourishment programs in Sri Lanka. This would be of immense use in future nourishment projects in the country.

Mining for Petroleum

Although Mining Engineering and Petroleum Engineering are two different fields of study, the two fields cross paths when it comes to the Oil Sands Industry. Oil Sands refers to the deposits of petroleum in the form of heavy bitumen being present in a mixture of sand or loosely consolidated sandstone. Because this heavy oil is too thick to flow and because it is thoroughly mixed with sand, the conventional methods of extraction of petroleum by drilling cannot be applied here. For this reason and also if the oil sand deposit lies relatively close to the surface, open pit mining is used to extract the oil sands. Once mined, the sands are processed to produce synthetic oil.

The mining for oil sands begins like in most mines by the overburden removal process. Common machinery such as excavators, bucket scrapers, and bulldozers are used to remove the overburden and the overburden is hauled by trucks and piled separately for refilling purposes. Once the overburden is removed and the oil sand layer exposed, the mining process begins. Since the oil sand deposits are unconsolidated, they can be easily be extracted by shovels or excavators. For this reason and for obvious safety reasons blasting is not performed. In addition to these machines, draglines and sometimes continuous excavators such as bucketwheel excavators are also used for mining the oil sands. The mined sand is hauled to a plant where the petroleum is extracted and refined by a variety of processes including crushing, froth flotation and distillation.

Although previously termed as an unconventional source of petroleum, the depletion of "conventional oil" and the associated rise in oil price has resulted in a shift of attention towards the oil sands industry. The largest oil sands deposits are located in Canada and Venezuela and the total volume of oil contained in the sands exceeds the conventional oil reserves of the world.  Oil sands have been commercially extracted in the Athabasca region in Canada since the 1930s and since have developed along with the advances in extraction technology. The following graph shows the value of sales  of oil sands and conventional crude oil in Canada and it can be seen that the oil sands sales have shown a significant rise during recent years.

value of sales of crude oil and oil sands (data taken from : http://www.capp.ca/library/statistics/Pages/default.aspx)

New methods have been developed to extract oil sands deposits that are too deep to extract using surface mining. These methods involve the reduction of the viscosity of the bitumen and the separation from the sand and enables the oil to be pumped to the surface. These methods are termed "In-situ methods". Cyclic Steam Stimulation (CSS), Steam Assisted Gravity Drainage (SAGD) and Toe to Heal Air Injection (THAI) are some of these methods. With advances in in-situ methods like these, the the recovery percentages of oil sands deposits have increased and now it can be considered as a viable alternative to conventional oil.

Limestone Mining in Pictures

In this post I have attempted to summarize the limestone mining process in pictorial form (and a video). Short descriptions have been included where necessary.

Overburden Removal

once the overburden is removed, the beds are cleaned and are prepared for drilling

Drilling

drilling is performed according to a pre determined pattern to accomodate explosives for blasting

Blasting

Rock Blasting is performed to fragment and loosen the consolidated limestone.

Loading and Hauling

Dispatching